VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201- 0696, TEL. (502) 778-2791 FORM 30900MODEL E36L SHOWN MODELS E24L, E36L,SERVICE MANUAL FOREL
10SECTION IIIREMOVAL AND REPLACEMENTOF SERVICEABLE PARTSWARNING: UNPLUG OVEN BEFORE SERVICING.WARNING: CERTAIN PROCEDURES IN THIS SECTION REQUIRE ELEC
113. Fold control manifold cover down and rest it on the crumb tray.REMOVAL OF INFINITE SWITCH1. Follow steps 1- 2 for dropping the control manifold c
125. Lay the manifold cover down so that it rest on the crumb tray. (Fig. 8)7. Remove the switch from the appliance.8. Reinstall new switch by revers
13REMOVAL OF ON-OFF AND 4-HEAT SWITCHS (EGO Hot top only)1. Pull crumb tray out about 6".2. Remove the screws at the top left and right corners o
14REMOVAL OF INDICATOR LIGHTS1. Follow steps 1-2 for dropping the control manifold cover.2. Lay the manifold cover down so that it is resting on the c
155. Squeeze the light mounting tabs in towards the light body casing and push the light through the manifoldcover opening and out of the appliance. (
164. Note and remove all wiring associated with thermostat. (Fig. 15)5. Lift up the left top aeration plate assembly to expose the top burner box area
179. Locate the bulb access hole in the oven cavity, top left hand corner, and carefully feed the bulband thermopile lead through the opening. (Fig.
1811. Reinstall the new thermostat by reversing steps 1-10.REMOVAL OF FRENCH PLATE1. Remove (2) bolts at top of control panel.2. Lower control panel.3
197. Note and remove (2) wires from the plate receptacle. (Fig. 22)Fig. 228. Remove the nut and locking bracket from the plate bottom. (Fig.23)Fig. 2
2SERVICE MANUAL FORELECTRIC RANGES MODELSE24L, E36L, E48L AND E60L SERIESIMPORTANT FOR YOUR SAFETYTHIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIE
209. Lift plate out of the aeration plate top.10. Install new french plate by reversing steps 1-9.REMOVAL OF HIGH SPEED ELEMENTS1. Remove the back ris
215. Install new element by reversing steps 1-4.When installing new element, be sure to align the element mounting tab with the mounting slotprovided
222. Using a 5⁄16" socket, remove (2) hex head screws from the upper corners of the control panel.3. Using a 5⁄16" socket, remove the hex h
236. Note and disconnect the wiring for the hot top section. (Fig. 30)7. Reinstall hot plate by reversing steps 1 through 6.Fig. 30
24REMOVAL OF GRIDDLE TOP1. Remove riser or back guard.2. Using a 5⁄16" socket, remove (1) 10-24 screw from the front burner box securing the to
25REPLACEMENT OF GRIDDLE TOP ELEMENTS1. Follow steps 1-3 under removal of griddle top.2. Using a 7⁄16" socket, remove griddle base cover by disen
26REMOVAL OF OVEN BOTTOM1. Open oven door.2. Remove oven rack(s).3. Lift oven bottom tray up and out of the appliance. (Fig. 35)REMOVAL OF THE BOTTOM
273. Lower the kick panel. (Fig. 37)Fig. 374. With a 5⁄16" socket, remove (2) screws holding the element terminal cover. Flip cover down. (Fig.
285. Note and disengage element terminal wiring. (Fig. 39)6. From inside the oven cavity, slip the bottom element out of the mounting clamps. Pu
29REPLACEMENT OF TOP OVEN ELEMENT1. Flip over the left hand top section or aeration plate and let it lay over one of the center top sections.(See Fig.
3TABLE OF CONTENTSDESCRIPTION PAGEIMPORTANT CODE, SAFETY AND WARNING INFORMATION 2DATA PLATE, ELECTRICAL, AND APPLIANCE CLEARANCE INFORMATION 3A
304. Open oven door and remove the oven rack(s). (Fig.43)Fig. 435. Loosen (19) top element clamps using a 5⁄16" socket. (Fig. 44)Fig. 44CAVITY A
316. Slip the element out of the clamps (clamps may require removal if turning them will not free the elementcompletely).7. Pull the element through t
324. From inside the oven cavity, located behind the front frame where the door is mounted, using a 7⁄16" socket,remove (2) nuts holding the door
333. Using a 5⁄16" socket wrench, remove (3) sheet metal screws securing the terminal block to the controlhousing. Remove the block from the appl
344. With a 5⁄16 socket wrench, remove the sheet metal screws securing the breaker to the control housing andslip the breaker out of the appliance. I
35SECTION IVWIRING DIAGRAMSFOR ADDITIONAL WIRING INFORMATIONCONTACT THE VULCAN-HART CO.SERVICE DEPARTMENT AT THEPHONE NUMBER LISTED ON THEBOTTOM FRON
36E24L
37E36L
38E48L
39E60L
4SECTION ISERVICE CHECKSWARNING: UNPLUG OVEN BEFORE SERVICING.WARNING: CERTAIN PROCEDURES IN THIS SECTION REQUIRE ELECTRICAL TEST ORMEASUREMENTS WHILE
5ON-OFF SWITCH CHECK1. Follow steps 1-3 under the 4-Heat switch check except, using an ohmmeter check for continuity in the offposition as follows:P1
6TROUBLESHOOTING PROBLEM CORRECTIVE ACTION Range is completely dead. Check to insure the main store power supply is on.Check to insure the appliance i
7TROUBLESHOOTING PROBLEM CORRECTIVE ACTION The circuit breaker trips after the range The slow trip of a circuit breaker is an indication of as been op
8SECTION IISERVICE ADJUSTMENTSWARNING: UNPLUG OVEN BEFORE SERVICING.WARNING: CERTAIN PROCEDURES IN THIS SECTION REQUIRE ELECTRICAL TEST ORMEASUREMENTS
9THERMOSTAT ADJUSTMENT1. Perform calibration check as stated under Section I.2. Remove the thermostat knob. (Fig 3)3. Insert a flat blade screwdriver
Commentaires sur ces manuels